Pro duct1-manufacture,factory,supplier from China

Manufacturing Process Broadcast1. Chipping: It is the manufacturing workshop of the raw materials in the whole board production. It mainly cuts loose wood into wood chips that meet the production specifications, so as to provide better conditions for fiber separation in preparation for heat.2. Thermal grinding. The wood chips cut out of the chipping workshop are preheated and cooked, and then mechanically separated to obtain fibers.3. Fiber drying: heat grinding and sizing to make the moisture content of the fiber reach 40%-50%.

Product performance  The most advanced flat pressing production line in the world. Therefore, the physical performance is higher and better than that of MDF. Its density is usually above 800kg/M3. The high-density fiberboard produced has reached 930kg/M3, which has reached the advanced level of similar products in Europe and America.   The board surface texture is fine and smooth.

Product performance    The most advanced flat pressing production line in the world. Therefore, the physical performance is higher and better than that of MDF. Its density is usually above 800kg/M3. The high-density fiberboard produced has reached 930kg/M3, which has reached the advanced level of similar products in Europe and America.     The board surface texture is fine and smooth. When the ambient temperature and humidity change, the size stability is good, and the surface decoration treatment is easy.

Oriented Strand Board Introduction:Oriented strand board (OSB), also called European pine board, is made of small diameter wood, interfelled wood, wood core, board veneer, branch Y wood, etc., and processed into 90-130mm long, 5-30mm wide and 0.5mm thick strands in the direction of wood grain by special planing equipment (long wood planer or two-stage chipping planing equipment), then dried, glued, and formed in the prescribed direction by hot pressing.

Variety of Wood Panel1. Low density fiberboard It is a panel made of wood or plant fiber shavings that are applied with a large amount of urea-formaldehyde glue and auxiliary materials. Its density is lower than 450 kg/m3, the fiber particles are larger, the internal structure is not uniform, the strength is relatively insufficient, and the weight is light.2. Medium density fiberboardIt is a board made of wood fiber or other plant fiber, added with urea-formaldehyde adhesive, and pressed under high temperature and high pressure.

     Density board is called medium density fiberboard（MDF) . It is made of wood fiber or other plant fiber, prepared by fiber, applied with synthetic resin, and pressed under heat and pressure. According to its density, it can be divided into high-density fiberboard, medium-density fiberboard and low-density fiberboard. It is widely used in the fields of furniture manufacturing and decoration in China.Xinhua Wood Show  Xinhua Wood Machinery  Gaotang County Xinhua Wood Industry Co., Ltd.

      Density board is called density fiberboard. It is made of wood fiber or other plant fiber, prepared by fiber, applied with synthetic resin, and pressed under heat and pressure.     According to its density, it can be divided into high-density fiberboard, medium-density fiberboard and low-density fiberboard.

     Density board, also known as fiberboard, is an artificial board made of wood fiber or other plant fiber by hot pressing after slicing, cooking, fiber separation, and drying, then applying urea-formaldehyde resin or other suitable adhesives.     The biggest advantage of MDF (medium fiberboard) is that it can be used for carving, engraving and milling, so as to make various shapes.

Xinhua Wood ProductsSpecification of  MDF for DecorationMDF BoardSize1220×2440mm or can be customized Thickness1mm-30mmMoisture6%-8%Core panelWood fiberColor wood color, surface can be made with different treatmentSurfacematt,embossed, glossy, leather,wave,synchronize etc...GlueE0/E1/E2/CARB P2/F4Applicationkitchen cabinets, wardrobe door, shoes cabinet, TV cabinet, funiture boardsMOQ1*20GP containerFree SampleAvailable at any timePackaging DetailsPackage of 4x8 MDF Board with 18mm thickness ;Items per Carton: 50 Pieces / Pallet;Items per Container: 8 Pallets / Contain

The differences between flame-retardant MDF and ordinary MDF are analyzed one by one as follows: 1. Color The color of flame-retardant MDF is dyed with red dye, so red MDF is not necessarily flame-retardant MDF Board, this point cannot be identified. 2. Physical and mechanical properties Due to the addition of flame retardants, the water-absorbing expansion of the board is affected to a certain extent. Therefore, testing the water-absorbing expansion coefficient of the board can preliminarily judge whether the flame-retardant MDF can meet the use requirements.

What are the common wood products in life that are MDF?    The common one may be the table. Some people think that the table should be made of solid wood, but in fact, many tables are made of density board, and then the surface is veneered to make the surface resistant to dirt and wear, and not easy to change color.

Fiberboard is a kind of man-made board made of wood fiber or other plant fibers with urea formaldehyde resin or other applicable adhesives. As it is soft and impact resistant, it has high strength, uniform density after pressing, and is easy to reprocess, but its disadvantage is poor water resistance.Advantages1.Fiberboard is easy to be coated.

MDF HDF Details  Size:1220*2440 1250*2500 or customized sizeThickness:1-30mmGlue:E0 /E1 /E2Material:Polar pine combiDensity:650-980 kg/m3Certificate:ISO, SGS, FSC,P2Moisture Content:4-6%Usage:for laminating board, furniture back panel, flooring, interior and exterior decorationMOQ:1X40HQPayment Term:T/T or 100% LC at sightPacking:Standard exporting palletsDelivery time:20 days after received dopositMDF HDF Properties    EN622-5:2009 MDF-GPPropertyTest MethodUnitRanges of nominal thickness (mm)1.8-2.52.5-44-66-99-1212-1919-3030-45＞45Swelling in Thickness 24 hEN317%45353

National Standard for Medium Density FiberboardMedium density fiberboard is a kind of man-made board with a density of about 0.5-0.88gcm3 after processing selected wood raw materials into fibers, adding urea-formaldehyde resin and other additives, and making it through a special process.

     It is said that wall panels originated in England in the 16th century. Everyone knows that the climate in England is cold and humid. In order to block the damp and cold lower part of the wall, wall panels are used for insulation.    Another theory goes back to the Netherlands in 1300. At that time, Europe was in the dark Middle Ages, and knights wearing armor and holding long swords often scratched the walls of castles or palaces inadvertently. Protect with wood.     At the beginning, wall panels were mainly used in castles and palaces.

Everyone knows that density board is widely used in making furniture or decorating partitions because of its uniform structure, fine material, stable performance and easy processing. Everyone is curious, how to distinguish the quality of density board?Let me tell you something.1. Surface cleanliness: There should be no obvious particles on the surface of the density board with good surface cleanliness. Particles are caused by impurities brought in during the pressing process, which not only affects the appearance, but also makes the paint film easy to peel off.2.

      The Invention of Wood-based Panels     The invention of wood-based panels can be traced back to 3000 BC. At the beginning of the 1st century BC, the Romans were already familiar with veneer manufacturing technology and plywood manufacturing principles.     In 1812, the French invented the veneer sawing machine.     In 1834, France issued a planer patent.     After 1844, the improved rotary cutting machine was officially used in industrial production.

Where are the functions of different density boards used?1. Standard board: Standard board is a material with a smooth side and a textured finish. It is used for cabinets, drawer bottoms and wall panels that belong to hidden parts.2. Glazed panel: Glazed panel is the surface layer that has been painted, often pasted with facing bricks or stamped into facing bricks or noodle patterns, used for wall panels or wall panels around bathtubs.3. Plastic veneer: Plastic veneer is used for sliding doors, which is good in decoration and easy to clean.

    HDF Fiberboard has a wide range of uses, and can be used instead of general boards in construction, furniture manufacturing, ships, and aircraft. Such as wall panels, floors, cement formwork, ceilings, hollow door panels, furniture panels, etc.        1. Furniture manufacturing: At present, fiberboard is mainly used to replace natural wood for furniture production. It can produce all kinds of panel combination furniture or disassembled furniture.        2.

        The reason why anything appears must conform to the laws of the market. The same is true for MDF, which can be widely used mainly because of its advantages in performance and cost.

App Features:Because of the three-layer criss-cross structure, Ozon board is more uniform than ordinary particle board, has better toughness, strong nail holding power, and is not easy to swell when it is damp. It is used as a house structure abroad and is strong. But it is relatively thick, the surface is uneven and difficult to handle, and it is rarely made into furniture.  When Ozon board came to China, it has almost become an upgraded substitute of large core board, with good quality and high price. It is especially suitable for the base layer of the background wall.

What is the main reason for the deformation of density board?The main reason for the deformation of the density board is the production process or the storage and use process.1.

MDF Mechanical propertiesBecause the fiber structure of the board is uniform and the bonding strength between fibers is high, its static bending strength, plane tensile strength, and elastic modulus are better than particleboard.

How to deal with the pungent smell of the density board?1） Keep the room ventilated and paint the MDF with anti-mildew paint.Put the density board in a dry place at home, keep the room ventilated, and it can be exposed to the sun if it is severely damp. Go to the market to buy anti-mildew paint and paint the MDF. It can play a certain role in preventing moisture and mildew, but pay attention to the quality of the paint and choose non-toxic and tasteless products.